How do you fix a PF on a Whirlpool dryer?
An LF (Lint Filter) Error Code indicates that the HybridCare™ filter has been removed. Place filter into dryer and make sure the handle is properly seated.
How do I reset my Cabrio dryer?
How to Reset a Whirlpool Cabrio
- Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
- Choose a new cycle and press “Start” to begin.
- Turn off and disconnect the Cabrio if the error or problem persists.
- Wait several minutes before restoring power.
What does PF error code mean?
power failure
Explanation. The PF Error Code indicates a power failure.
What does PF mean on a Whirlpool?
a power failure
The PF Error code indicates that the unit has experienced a power failure during operation. Some models may allow you to hit “Start” to complete the cycle. For other models, you may need to hit “Cancel” and restart the machine from the beginning.
How do I fix the code on my lf Whirlpool Cabrio washer?
LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
What are codes on a Whirlpool dryer?
What do your tumble dryer error codes mean?
- F01 — Electronic circuit board fault.
- F02 — Motor circuit fault.
- F05 — Waste pipe blockage or pump issue.
- F06 — Door lock fault.
- F07 — Electronic circuit board fault / heating circuit fault.
- F08 — Heater fault.
- F09 — Software fault.
- F11 — Pump circuit fault.
What does PF mean on Cabrio dryer?
Power failure
PF – Power failure. This happens when power is interrupted while the dryer is running. Press START to continue the cycle or STOP to clear the PF from the display. If the code reappears, check the pigtail (power cord) for damage or bad connections.
Is there a reset button on Whirlpool Cabrio dryer?
Whirlpool dryers can do many things, such as monitor moisture levels and temperature, reduce noise, periodically tumble clothes to remove wrinkles, steam clothes and adjust the overall drying time according to fabric and load size. However, one thing a Whirlpool dryer cannot do is reset itself by pushing a button.
How do I fix PF error on my LG washer?
The PF error code indicates a power failure. This may occur if the power supply to the washer is interrupted during a cycle from power outage. To fix this: Simply restart the washing cycle process.
How do I remove the PF code from my Whirlpool washer?
A PF (Power Failure) error code indicates that the wash cycle was interrupted by a power failure. Touch and hold START to restart the washer cycle or press POWER to clear the display.
How do I reset my Cabrio washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
What does PF mean on a Cabrio dryer?
Why does my dryer Flash PF?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
Is there a reset button on my Whirlpool dryer?
Why does my washing machine say PF?
What does PF mean on a whirlpool dryer?
what does the code PF mean on a Whirlpool dryer? The whirlpool Cabrio dryer PF error means the main control has had a power failure from either a loss of voltage from the power supply or the board itself. Usually a power surge causes the PF error and is easily reset.
How to fix a whirlpool Cabrio?
Disconnect the power to the washer.
Why is my Whirlpool Cabrio washer not draining?
Why is my Cabrio washer not draining? Check the washer’s discharge hose if the water fails to drain from the washtub. Look for any kinks in the Cabrio washer’s discharge hose that could stop the water from draining. Straightening the hose ensures proper draining. Test the drain pump to ensure it has not failed if the washer still will not drain.
How to fix Whirlpool Cabrio dryer F01 error?
Disconnect the equipment from the mains.