What is the post spacing on a split rail fence?
Classic Split Rail post rail spacing starts 6 inches from the top and then holes are spaced every 16 inches. Both Classic and Appalachian styles use the same 11 foot sawn and paddled fence rail that is pressure treated with a wood preservative to protect it from decay and termite damage.
How deep should split rail posts be?
Dig holes about a third as deep as they are tall. For example, a 6-foot post needs a hole at least 2-feet deep, plus add about 4-inches for gravel. The diameter of the hole should be three times the width of the post. Ensure that the bottom rail will remain a few inches above ground.
How far apart should posts be for a 11 split rail fence?
10ft
However, remember to ask the fence supply company how long each of the rails are. Some of the commonly available options are 9 feet long and 11 feet long rails. Knowing this measurement would help you to space the posts accordingly. 9ft rails have post every 8ft and 11ft rails have post every 10ft.
How high should a split rail fence post be?
Set split rail height. Each post needs to be marked at 36 inches from its bottom end. This leaves 24 inches for the depth of the whole and 12 inches from the ground to the first railing. Once marked, you can lay a post next to each spray painted post hole marker.
Do you need to use concrete for split rail fence posts?
No, the hole should be filled only with the dirt that came out of the hole and tamped back in . Concrete is bad for the wood (erodes it), and gravel simply creates a porous pocket where water can collect. Well tamped soil is very stable and waterproof. Some people use concrete for gate posts for additional stability.
Should I concrete split rail fence posts?
You shouldn’t set split rail fence posts in concrete, as traditionally, these wooden fence posts are designed to be repairable, and setting them in concrete would make them impossible to replace if they rot. Impermeable soil causes water to sit in the pot your hole created and rot.
Should I Concrete split rail fence posts?
Should I use pressure treated wood for fence rails?
When used for fencing, it must be pressure-treated to stand up to decay and the elements. It resists shrinkage, but it can still warp, crack, or twist. When properly treated, it can last a lifetime, even if it comes in contact with wet soil.
Which lasts longer cedar or pressure treated?
When it comes to comparing treated wood vs. cedar, pressure-treated wood is the sturdier and more weather-proof of the two. It’s highly resistant to insect attack and rot, and special versions rated for “ground contact” can be buried in soil and will continue to shrug off decay for decades.
How far should a 4 foot post be in the ground?
The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.
How long will pressure treated split rail fence last?
about 9 and 25 years
Pressure Treated Rails Pressure treated wood will usually last about 9 and 25 years, so it comes in just under the natural cedar. This type of treated wood is also filled with chemicals – those can leach out into the surrounding ground, which is why it should never be used near potable water sources or food gardens.
Where can I get a split rail fence in Cincinnati?
This is a very common fence installed throughout the greater Cincinnati and Tri-state area, and is written in many homeowner’s association bylaws. Eads Fence Company is the complete source for all your split rail fence material and installation needs in the Tri-State area.
What are splitsplit rail fences?
Split Rail Fences are timeless, beautiful and affordable. They add rustic charm to any property, and serve many purposes. There are several styles and are typically made from locust & hemlock or treated poplar & pine, along with a few other materials.
What are your split rail gates made of?
Our split rail gates are constructed of thick rough cut pine. They have a through bolt construction for added strength. We hang our gates with a J-bolt or Strap hinge for a tighter fit and wider swing.