Can you replace spindles on a trailer?
Expert Reply: To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel tracking problems.
How do I know what size bearings to get for my trailer?
The easiest way to determine which bearings are used on your trailer axle is to take the hub off and check for the numbers stamped into the bearings. If the bearing numbers cannot be read, the next best solution is to find the bearings’ inner diameter.
What size spindle is on a 3500 lb axle?
3500 lb axles have the most common and most consistent spindle sizes. They are typically 1.73 inches at the seal, 1.38 inches at the inner bearing and 1.06 inches at the outer bearing like # TRU24FR.
What is a number 84 spindle?
This is a Weld in Trailer Spindle that will accommodate a 3500 lb Straight Trailer axle Beam and corresponding wheel bearings. This Spindle is referred to as a #84 Spindle, using a 1 3/8″ ID Inner Wheel Bearing and a 1 1/16″ ID Outer Wheel Bearing. Additionally, this Spindle uses the standard 1.72″ ID Seal Surface.
How much does it cost to replace a spindle?
Some Factors That Affect Spindle Repair Cost For instance, a damaged tool interface may add between $700 and $1,600 depending on the size and style. Damaged bearing journals can add between $400 and $1,400. A damaged shaft can add $4,000, often doubling the cost of a base repair.
How do I know my spindle size?
How do I determine what size spindle I have?
- 1 1/16”
- 1 ¼”
- 1 ⅜”
- 1 ¾” The second method is by using a flexible tape measure. Wrap the tape around the spindle at the bearing locations. The number is the circumference of the spindle. Use the table below to determine the bearings required for your spindle.
What size spindle do I need?
The best way to find out which spindle length you need is by looking up the specs. (The alternative is trial and error…) Spindle length and the resulting chainline have some leeway. If you are within 2-3 mm of the “correct” 43.5 mm or 45 mm, you are doing quite well.
What is a hub bore size?
The outer diameter is the hub bore, while the inner diameter is the diameter of the vehicle hub itself. For example: a hub-centric ring size of 73-67.1 would mean that the wheel center bore is 73 mm wide and the vehicle hub is 67.1 mm wide.
Do I really need hub centric rings?
Do I need Hubcentric Rings or Hubcentric Adapters? Yes, if your wheel center bore is a larger diameter than your hub bore, you absolutely need hubcentric rings. This is because aftermarket wheels are typically designed to fit as many cars as possible unless they are custom-made for your specific application.
Can you weld on a trailer axle?
If you’re interested in welding your own trailer axle, then we can provide the perfect kit to help you get the job done. Our weld-your-own trailer axle kits come with the spindles, hubs, and bearing kits that you need to get started on your axle. All you’ll need is the axle beam!
How do you get a spindle out of a trailer axle?
Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw. Then to replace the spindle such as with the EZ Lube # TRU37FR that you were looking at it’s extremely important that it be done by a certified welder who is experienced with this type of job.
How long does it take to change a spindle?
A quick turnaround for an emergency spindle repair job would be 24 hours, but the standard turnaround time for a straight repair is between 5-10 business days. In some unique cases, depending upon the need to make repairs or obtain new parts, a spindle repair job can take a few weeks.
Are spindle and knuckle the same?
The knuckle is the part the spindle attaches to. The spindle carries the hub and bearing(s). Generally the spindle is used on non-driven wheels, but there are some where the spindle is hollow and the CV shaft extends through e.g. Some Nissan’s.