How far should your indicator be from your fly?
The general rule of thumb is that the distance between your strike indicator and your fly should be approximately one and a half times the depth at which you wish to wish to fish your fly.
Can you use an indicator with a dry fly?
Another time an indicator is required in when fishing size twenty and smaller dry flies. In this case an indicator is necessary to keep track of the fly. In this case the indicator is usually another fly that you can see, or a conventional small strike indicator will also work.
Where do you put the strike indicator in fly fishing?
As for where to attach the indicator to the leader, it depends how deep you want to fish. If you want to fish toward the surface, attach your indicator one to two feet from the end of the leader. If you want to fish deeper, attach the indicator further from the end of the leader.
Do you need a strike indicator with nymphs?
No, you do not need to use a strike indicator. This is known as “naked nymphing”, and at times, it may actually increase your odds of catching a fish. In particular, you should consider removing your indicator when you are fishing shallow water, stillwater, or sight-casting to fish feeding beneath the surface.
How do you use fly fishing strike indicators?
Simply attach your indicator at the desired depth so your flies will be suspended beneath, cast out gently using an open loop and a slowed down casting stroke and present them gently on the water surface. After they’ve landed, do a long straight pull to remove any slack and keep the flies in line with your rod.
Do you need a strike indicator for nymphs?
How do you become a nymph without an indicator?
8 Tips for Nymphing Without an Indicator
- Lead Your Fly Line.
- Stay Connected.
- Fish as Short a Line as Possible.
- Keep as Much Fly Line off the Surface As Possible.
- Watch For Ques.
- Use a Highly Visible Fly Line.
- Set on Anything.
- Keep Your Fly in the Water.
Do strike indicators spook fish?
One of the biggest drawbacks to floating strike indicators like the Thingamabobber (link to AMAZON for price check) is their fish-spooking ability. Especially in clear water, the splash landing of a strike indicator can send trout scattering in all directions and put them off the feed for the rest of the day.
How do you use an indicator for fly fishing?
Generally, your indicator should be placed approximately one and a half times the depth of the water up your leader from the bottom fly. So, if you’re fishing a run around three feet deep, place your indicator around four and a half feet up from your fly.
How can we keep the New Zealand strike indicator floating?
While the typical “thingamabobber” or floating cork might do the trick, often times these could spook fish lying beneath the surface. Luckily the New Zealand Strike Indicator Company created a reusable system using yarn and tubing that casts like a dream and floats for hours on end.
Can you fish nymphs without an indicator?
How do you fish indicator fishing?
If it’s windy (and indicator fishing often works best when there’s a bit of ripple) you can let the wind make a bow in the line and move your flies round. As the line straightens out the bow, start twiddling the line back and often the trout will take the flies as they change direction.
Do you use too many indicators when fly fishing?
However, there are plenty of fly fishing purists out there who believe that relying too much on an indicator means that you aren’t learning techniques and are relying too much on devices to do the hard work for you.
How do I Fly FISH using a Bobber or indicator?
How do I Fly Fish Using a Bobber or Indicator? Simply tie the bobber onto your fly line, at the exact position of your set depth. Cast out onto the water using a smooth motion, and leave the fly inside the water. You may want to move the rod slightly to the right while tracking the bobber as it moves along the surface of the water.
How do you use a fly rod indicator?
Simply attach your indicator at the desired depth so your flies will be suspended beneath, cast out gently using an open loop and a slowed down casting stroke and present them gently on the water surface. After they’ve landed, do a long straight pull to remove any slack and keep the flies in line with your rod.